溶胶-凝胶法制备NixCo1-xCoAlO4尖晶石型复合氧化物及其催化分解N2O性能

用溶胶凝胶法制备了一组Ni_xCo_1-xCoAlO₄尖晶石型复合氧化物,并采用表面润湿浸渍K₂CO₃溶液进行了K掺杂改性,用于有氧气氛下的N₂O催化分解反应.采用N₂物理吸附、X-射线衍射(XRD)、扫描电镜(SEM)、H₂-程序升温还原(H₂-TPR)等技术对催化剂进行了表征,考察了催化剂组成、母液pH值、K负载量等制备参数对其催化活性的影响.结果表明,母液pH值为3、K/(Ni+Co)物质的量比为0.1的K/Ni_0.15Co_0.85CoAlO₄催化剂具有较高的N₂O分解活性,450 ℃ N₂O可完全分解.助剂K的加入弱化了催化剂表面金属氧键,提高了催化剂的还原性、催化活性和抗水性.     

Lithium‐Salt‐Containing High‐Molecular‐Weight Polystyrene‐block‐Polyethylene Oxide Block Copolymer Films

Ionic conductivity in relation to the morphology of lithium‐doped high‐molecular‐weight polystyrene‐block‐polyethylene oxide (PS‐b‐PEO) diblock copolymer films was investigated as solid‐state membranes for lithium‐ion batteries. The tendency of the polyethylene (PEO) block to crystallize was highly suppressed by increasing both the salt‐doping level and the temperature. The PEO crystallites completely vanished at a salt‐doping ratio of Li/EO>0.08, at which the PEO segments were hindered from entering the crystalline unit of the PEO chain. A kinetically trapped lamella morphology of PS‐b‐PEO was observed, due to PEO crystallization. The increase in the lamella spacing with increasing salt concentration was attributed to the conformation of the PEO chain rather than the volume contribution of the salt or the previously reported increase in the effective interaction parameter. Upon loading the salt, the PEO chains changed from a compact/highly folded conformation to an amorphous/expanded‐like conformation. The ionic conductivity was enhanced by amorphization of PEO and thereby the mobility of the PEO blocks increased upon increasing the salt‐doping level.     

高温水解-离子色谱法测定钴酸锂中氯

使用高温水解-离子色谱法对钴酸锂中痕量的氯进行分析测定。样品在1 100℃高温下通入氧气与水蒸气进行水解反应,生成氯化氢气体随载气带出,经冷凝后接收,并通过离子色谱法对氯的含量进行测定。以NaHCO3(4.5mmol/L)与Na2CO3(2.7mmol/L)的混合溶液为淋洗液,经SH-AG-1保护柱及SH-AC-1分离柱分离,Cl-在0.05~5.00mg/L范围内浓度与峰面积呈线性关系,检出限(3S)为0.010mg/L。方法测定氯的加标回收率在92%~96%,相对标准偏差(n=11)在3.0%~5.3%,方法准确、可靠。     

Preparation and Electrochemical Properties of Tin–Iron–Carbon Nanocomposite as the Anode of Lithium‐Ion Batteries

Tin–iron–carbon nanocomposite is successfully prepared by a sol–gel method followed by a chemical vapor deposition (CVD) process with acetylene gas as the carbon source. The structural properties, morphology, and electrochemical performances of the nanocomposite are comprehensively studied in comparison with those properties of tin–carbon and iron–carbon nanocomposites. Sheet‐like carbon architecture and different carbon contents are induced thanks to the catalytic effect of iron during CVD. Among three nanocomposites, tin–iron–carbon demonstrates the highest reversible capacity of 800 mA h g^?1 with 96.9 % capacity retention after 50 cycles. It also exhibits the best rate capability with a discharge capacity of 420 mA h g^?1 at a current density of 1000 mA g^?1. This enhanced performance is strongly related to the carbon morphology and content, which can not only accommodate the large volume change, but also improve the electronic conductivity of the nanocomposite. Hence, the tin–iron–carbon nanocomposite is expected to be a promising anode for lithium‐ion batteries.     

定量的复合金属锂作为三维泡沫锂电极用于锂电池的研究

金属锂作为电池的负极材料具有极高的比容量和极低的氧化还原电位,能够显著提升电池的能量密度。然而,金属锂负极在实际应用中所面临的主要问题是锂枝晶、界面副反应和电极体积变化大的难题。在本文中,我们提出了一种通过将定量的金属锂与三维骨架进行复合形成三维泡沫锂负极的策略,并利用三维泡沫锂来抑制锂枝晶的生长和缓解电极的体积变化。因此,三维泡沫锂电极有利于金属锂负极的高效利用,并能借助其与平面锂箔相比更高的比表面积和更多的反应位点来提升电池的倍率性能。因此,通过采用三维泡沫锂,对称电池的循环寿命和倍率性能都得到了有效的提升。EIS数据结果表明,三维泡沫锂能够减小对称电池的电荷转移阻抗。而且,将三维泡沫锂作为负极组装的LTO全电池,与锂箔作为负极相比,循环1000周平均放电比容量从65 mAh·g^-1提升至121 mAh·g^-1。     

热熔灌输法制备三维骨架支撑金属锂复合负极

金属锂因具有极高的理论比容量(3860 mAh/g)和最低的电化学势(相对于标准氢电极为-3.04 V),被认为是下一代高比能锂离子电池的首选负极材料。然而,金属锂负极在电池循环过程中发生的刺状枝晶生长和体积变化等问题严重阻碍了其产业化应用进程。近年来研究表明,通过在金属锂中引入具有三维(3D)结构的宿主骨架,不但能有效抑制锂枝晶的生长,而且可以缓解金属锂负极的体积变化,从而提高金属锂电池的循环性能与安全性。因此,设计3D骨架/金属锂复合负极被认为是一种能有效解决金属锂问题的新兴策略。本文综述了热熔灌输法制备3D骨架/金属锂复合负极的研究进展。首先讨论了当前基于3D骨架的预存金属锂技术,然后着重分析了热熔灌输策略中3D骨架锂润湿性的影响因素,以及不同3D骨架修饰特征和改性方法。最后对3D骨架/金属锂复合负极和热熔灌输策略现存问题进行了总结并提出未来的发展方向。     

超微Ni(OH)2纳米粒子的合成及其对Li+的超高吸附性能

在葡萄糖水溶液中合成得到平均粒径为5 nm的α-Ni(OH)2超微纳米粒子。研究结果发现,在水溶液中葡萄糖浓度能够控制α-Ni(OH)2纳米粒子粒径的大小,我们对其中的原理进行了剖析。当没有葡萄糖存在时,合成得到的Ni(OH)2晶型为β型,且颗粒粒径尺寸分布为微米级别。另外,研究发现α-Ni(OH)2超微纳米粒子室温下对中性水溶液中Li^+具有较强的吸附性能,且这种吸附性能随粒径的减小而剧烈增大;粒径为5 nm的α-Ni(OH)2粒子对Li^+的最大吸附量为214 mg·g^-1(远大于文献报道的有关吸附剂对Li^+的吸附容量),而粒径为1μm的β-Ni(OH)2在相同条件下对Li^+的最大吸附量低于30 mg·g^-1。计算分析表明,Li^+在α-Ni(OH)2纳米粒子表面吸附满足Freundlich方程,符合层层吸附模型。     

水洗和回烧工艺对高镍三元材料LiNi0.88Co0.07Al0.05O2微观结构及电化学性能的影响

以镍钴氢氧化物、异丙醇铝为原料,采用水解法合成三元前驱体Ni_(0.88)Co_(0.07)Al_(0.05)O_2,再与锂盐混合烧结得到正极材料(TEM)、X射线光电子能谱(XPS)、能量色散X射线谱(EDS)和恒电流充放电测试等对样品的晶体结构、微观形貌、元素价态以及电化学性能进行表征。研究表明,料液比1∶25、水洗3次、600℃回烧2 h合成的LiNi_(0.88)Co_(0.07)Al_(0.05)O_2具有较优的综合电化学性能,其在0.2C的放电比容量达207.6 mAh·g~(-1),首次充放电效率为84.8%,1C放电比容量为192.0 mAh·g~(-1),循环100周后,材料的放电比容量仍有148.0 mAh·g~(-1),容量保持率达到77.1%。     

Needle-like cobalt phosphide arrays grown on carbon fiber cloth as a binder-free electrode with enhanced lithium storage performance

Cobalt phosphide(CoP) is a promising anode candidate for lithium-ion batteries(LIBs) due to its high specific capacity and low working potential.However,the poor cycling stability and rate performance,caused by low electrical conductivity and huge volume variation,impede the further practical application of CoP anode materials.Herein,we report an integrated binder-free electrode featuring needle-like CoP arrays grown on carbon fiber cloth(CC) for efficient lithium storage.The as-prepared CoP/CC electrode integrates the advantages of 1 D needle-like CoP arrays for efficient electrolyte wettability and fast cha rge transpo rtation,and 3 D CC substrate for superior mechanical stability,flexibility and high conductivity.As a result,the CoP/CC electrode delivers an initial specific capacity of 1283 mAh/g and initial Coulombic effeciencies of 85.4%,which are much higher than that of conventional CoP electrode.Notably,the Co P/CC electrode shows outstanding cycling performance up to 400 cycles at 0.5 A/cm² and excellent rate performance with a discharge capacity of 549 mAh/g even at 5 A/cm².This work demonstrates the great potential of integrated CoP/CC hybrid as efficient bind-free and freestanding electrode for LIBs and future flexible electronic devices.     

碳酸酯类电解液中Mg(NO3)2添加剂抑制锂枝晶生长的研究

在锂-硫化聚丙烯腈电池体系中,负极锂枝晶的形成和生长严重恶化了电池充放电性能,并给电池带来了安全隐患。而在更有利于稳定正极硫化聚丙烯腈材料的碳酸酯类电解液中,锂枝晶生长尤为严重。本文通过将硝酸镁添加到碳酸酯类电解液中,研究硝酸根和镁离子对锂金属表面改性的共同作用。实验数据发现,在硝酸根和镁离子共同作用下,锂枝晶生长被有效抑制。当硝酸镁浓度为100 mmol·L^-1时,锂铜半电池的库仑效率明显提高,并显著改善了锂-硫化聚丙烯腈电池的循环性能。300次循环后容量保持率为71%,远高于硝酸锂的61%和无添加剂的50%。